Publish Time: 2022-07-18 Origin: Safetoe Academy
Electrical work creates a different type of footwear risk.Electricians, utility workers and industrial maintenance teams may work around energized equipment while also facing ordinary workplace hazards such as falling objects, sharp debris, slippery floors and long hours on hard surfaces.
For this reason, electrical safety footwear should not be selected simply because a boot looks heavy-duty or has a safety toe.
One of the most common specifications buyers see is:18kV EH Rated. But what does 18kV actually mean?Does it mean workers can safely work on an 18,000-volt circuit while wearing the boots? No.The 18kV figure refers to a controlled laboratory electrical hazard test. It should not be interpreted as the safe working voltage of the footwear.
This guide explains what EH means, how 18kV electrical hazard footwear is tested, what its limitations are and what industrial buyers should check when selecting safety footwear for electrical work.
EH stands for Electrical Hazard.EH footwear is designed to provide secondary protection against accidental electrical contact by helping reduce the possibility of current passing from the wearer through the footwear to the ground.
Under the ASTM safety footwear system, EH is an additional protection category.A boot should only be described as EH rated when the relevant electrical hazard performance has been verified and the corresponding marking appears on the product documentation and footwear.
EH footwear is particularly relevant to applications such as:
Electrical maintenance
Power utilities
Electrical contractors
Substations
Industrial manufacturing
Machinery maintenance
Renewable energy installations
Construction electrical work
However, EH protection should always be considered one part of a complete electrical safety program.It does not replace insulating gloves, insulating mats, arc-rated PPE, safe isolation procedures or other primary electrical protection.
This is the most important point for buyers to understand.Under the ASTM EH test method, footwear is subjected to a high-voltage laboratory test under specified dry conditions.
The commonly referenced EH test conditions are:
18,000 volts AC
60 Hz
1 minute
Maximum leakage current: 1.0 mA
Passing this test demonstrates the electrical resistance performance required for the EH classification under controlled laboratory conditions.
This distinction is critical.A boot passing an 18kV EH laboratory test does not mean a worker is permitted to intentionally contact or work directly on an 18kV energized system while relying on the footwear for protection.
EH footwear is intended as secondary protection against accidental electrical contact.The actual electrical work must still follow the employer's electrical safety procedures, risk assessment and applicable regulations.
18kV Laboratory Test ≠ 18kV Safe Working Voltage
This should always be made clear in purchasing specifications, product training and end-user communication.
Electrical safety footwear buyers frequently see both ASTM F2412 and ASTM F2413 referenced.They have different roles.
ASTM F2412 specifies the test methods used to evaluate protective footwear.These methods cover several types of performance, including electrical hazard resistance, impact resistance, compression resistance and puncture resistance.
ASTM F2413 defines the performance requirements and classifications that protective safety-toe footwear must meet.For new U.S.-market projects, buyers should check the actual edition stated on the product documentation.
The current Safetoe M-8356RB documentation references:ASTM F2413-24 I/C EH PR
This indicates protection categories including:
I — Impact protection
C — Compression protection
EH — Electrical Hazard protection
PR — Puncture Resistance
Buyers should always verify the complete marking rather than purchasing footwear based only on the words “electrical safety boot.”
Electrical hazard footwear should not be treated as the worker's primary electrical insulation.Its purpose is to provide an additional protective layer if accidental contact occurs.
For example, an electrical worker may also require:
Appropriate electrical insulating gloves
Arc-rated clothing
Electrical protective helmets
Insulating mats or blankets
Correct tools
Lockout/tagout procedures
Safe working distances
De-energization procedures
The required PPE depends on the electrical task and workplace risk assessment.A pair of EH boots alone cannot make live electrical work safe.This is why buyers should be cautious with descriptions such as:
"18kV insulated boots for live electrical work"
Unless the footwear has been specifically tested and certified to the appropriate dielectric footwear standard for that type of application, this description may be misleading.EH footwear and specialized dielectric insulating footwear are not automatically the same thing.
This distinction is especially important for electrical utility buyers.
EH footwear is typically occupational safety footwear that combines electrical hazard resistance with other industrial protection features.
Typical features may include:
Safety toe protection
Puncture resistance
Electrical hazard resistance
Slip-resistant outsole
Industrial upper construction
Comfort support
It is intended to provide secondary electrical protection.
Specialized dielectric footwear is designed around specific electrical insulation requirements and may be tested according to a different standard or electrical class system.Such footwear may be required for particular high-voltage electrical operations.
Therefore:
Do not select electrical footwear based only on the highest voltage number printed in a product description.
Electrical resistance can change when footwear becomes wet, damaged or contaminated.Moisture can significantly reduce the insulating performance of footwear materials.
For this reason, EH footwear should not be treated as electrical protection in conditions where water, excessive moisture or contamination could compromise its protective properties.
Before use, workers should check the footwear for:
Wet or saturated materials
Cracks
Deep cuts
Damaged outsoles
Sole separation
Embedded metal particles
Severe wear
Punctures
Damage around the upper or sole connection
If the footwear is damaged in a way that could affect its electrical resistance, it should be removed from service and evaluated or replaced according to the employer's safety procedure.
Not necessarily.A common misconception is:
"Electrical safety boots must contain absolutely no metal"
EH performance is determined by the tested electrical resistance of the complete footwear construction—not simply by whether one component contains metal.However, many electrical safety footwear designs use composite components because they can reduce unnecessary conductive materials while also lowering weight.
Safetoe M-8356RB uses:
VortiGard™ Composite Toe Protection & FlexBarrier™ Puncture Protection
This configuration provides toe and underfoot protection without relying on a conventional steel toe and steel midsole.For many electrical contractors and industrial buyers, this is a practical configuration.
But the most important factor remains:
Verify the completed footwear against the required electrical safety standard
Electrical workers rarely face only electrical hazards.
A realistic footwear specification should consider all major workplace risks.
Electrical contractors may work around tools, machinery, cable drums and industrial equipment.
Certified toe protection helps reduce the risk of injuries caused by falling or rolling objects.
Construction and maintenance areas may contain nails, metal fragments and other sharp debris.
Puncture-resistant construction can provide additional underfoot protection.
Industrial floors may contain water, oil, dust or other contaminants.
Appropriate outsole performance is therefore another important selection factor.
Electricians and maintenance workers often remain on their feet throughout the shift.
Cushioning, support, fit and breathability can influence worker comfort and compliance.
This is why professional electrical safety footwear should be selected as a complete safety system rather than based only on the EH marking.
For electrical contractors, utility projects and industrial maintenance applications, Safetoe offers the M-8356RB 18kV EH Rated Electrical Hazard Safety Work Boot.
Upper: Full-Grain Smooth Cow Leather
Toe Protection: VortiGard™ Composite Toe
Puncture Protection: FlexBarrier™ Puncture-Resistant Construction
Outsole: PlumaShield™ PU/Rubber Outsole
Lining: BactiVoid™ Breathable Sandwich Mesh
Insole: Anti-Fatigue Memory Foam Insole
Sizes: EU 37–47 / UK 3–13 / US 4–14
ASTM F2413-24 I/C EH PR
EN ISO 20345:2022+A1:2024 SB PS SR FO CI HI HRO
For distributors, project buyers and EHS teams, the following process is more reliable than selecting footwear based on product appearance.
Identify the standard specified by the project or local market.
For U.S.-oriented projects, this may include ASTM F2413 with EH protection.
Other markets may require different standards.
Do not accept a generic statement such as: electrical safety shoes
Check the actual marking and supporting test documentation.
Ask whether workers also require:
Impact protection
Compression protection
Puncture resistance
Slip resistance
Waterproof performance
Heat resistance
Cold insulation
Metatarsal protection
Indoor factory maintenance and outdoor utility work may require very different footwear configurations.
For bulk purchases and tenders, buyers should request the relevant test report, technical datasheet and compliance documentation.
The model number shown on the product should correspond with the supporting documents.
A reliable safety footwear label should identify the applicable standard and the protection categories the product has been tested for.
For example:
ASTM F2413-24
I/C
EH
PR
The exact layout may vary, but buyers should confirm that EH appears where electrical hazard protection is required.
Do not assume a boot provides EH protection simply because:
It has a rubber outsole
It uses a composite toe
It contains no metal
It is marketed for electricians
It looks insulated
The actual standard marking and supporting documentation matter.
Proper care is important because wear and contamination can affect footwear performance.
Before each use:
Inspect the outsole for cuts, punctures and excessive wear.
Check for embedded metal or conductive debris.
Confirm the upper and outsole are securely bonded.
Do not use damaged footwear where electrical resistance may be compromised.
Keep the footwear dry when relying on EH performance.
For cleaning:
Use suitable footwear cleaning products and avoid aggressive chemicals that may damage the materials.
Allow wet footwear to dry naturally and follow the manufacturer's care instructions.
For project PPE programs, periodic inspection and replacement procedures should form part of the workplace safety system.
18kV refers to the laboratory test voltage, not permission to intentionally work on an energized 18kV conductor.
Composite toe construction alone does not establish EH compliance.
The complete footwear must meet the required electrical hazard test.
Electrical resistance can be compromised by moisture or contamination.
Electrical workers may also need toe, puncture, slip and comfort protection.
For new projects, verify the exact standard edition stated on the product documentation.
No. The 18kV figure refers to a controlled laboratory test voltage. It is not the footwear's permitted working voltage. EH footwear is intended as secondary protection against accidental electrical contact.
ASTM F2412-24 provides the footwear test methods, while ASTM F2413-24 defines the current performance requirements and classifications for protective safety-toe footwear.
Composite toe caps can reduce the use of conductive metal components and may also reduce footwear weight. However, composite toe construction alone does not guarantee EH performance. The completed footwear must be tested to the required standard.
No. EH footwear is occupational safety footwear providing secondary electrical hazard protection. Specialized dielectric insulating footwear may be tested under different standards for particular electrical applications.
Common applications include utilities, electrical contracting, substations, manufacturing maintenance, energy infrastructure, machinery service and construction electrical work.
Choosing electrical safety footwear is not simply a matter of finding a boot marked "18kV." Professional buyers should understand what the EH designation actually means, verify the applicable standard and select footwear based on the complete workplace hazard assessment.
The most important principle is simple: 18kV is a laboratory EH test condition — not a safe working voltage
Electrical hazard footwear should always be used as secondary protection together with appropriate electrical PPE, safe work procedures and workplace controls.For electrical utility projects, industrial maintenance programs and distributor requirements, Safetoe offers EH safety footwear including the M-8356RB 18kV EH Rated Electrical Hazard Safety Work Boot.
Explore Safetoe Electrical Safety Footwear Solutions
Safety Shoes in Qatar: How to Choose Anti-Slip Work Boots for Construction & Warehousing
18kV EH Safety Shoes: What Electrical Workers and Buyers Need to Know
How to Choose Oil & Gas Safety Boots for Middle East Projects: 3 Recommended Models
Top Foot Hazards in Mining and How Safety Boots Reduce Workplace Injuries
Safety Shoes & Safety Boots | S1 S3 Steel Toe Slip Resistant Work Shoes
Steel Toe vs Composite vs Aluminum: What Works Best for Long Shifts & Heat?